Item name: F405 V1.1 Flight Controller
Input power: 12.6-25V (3-6S)
BEC: 5V/1.5A
MCU: STM32F405
Gyro: MPU6000
Flash: 16MB
OSD: AT7456
Mounting hole: 30.5*30.5mm
Weight: 6g
Product Parameters
Name: Aocoda-RC F4 special flight controller for Jingsu Huafei
Main control chip: STM32F405RGT6
MPU: MPU6500
Character overlay: AT7456E
Black box: integrated 16M Flash
Barometer: BMP280
Serial port: 4 optional
Motor output: 8 channels optional
LED strip: support
Buzzer: support
Input voltage: 3-6S Lipo
Power output: 5V/2A, 9V/2A
Weight: 6.0g
Size: 36x36mm, mounting hole 30.5mm
Firmware: AOCODAF405
Note: the board is V1.1 Vsersion now.
45A BLHELI_S 4IN1 3-6S Brushless ESC Support DShot 300-600 / Multishot / Oneshot / PMW 30.5*30.5mm For RC FPV Racing Drone
Size: 41*39.5*5mm
Hole distance: 30.5*30.5/5mm (3mm hole diameter after installing the shock-absorbing ball)
Weight: 13g
Input voltage: LIPO 2-6S
Continuous current: 45A
Maximum current: 50A (10 seconds)
Processor: EFM8BB21F16G
Firmware: BLS J_H_30_REV16_7
Drive signal support: DShot300-600/Multishot/Oneshot/PMW
Current sensor: Support
RuiBet 45A BLHELI_S Dshot600 3-6S Brushless 4in1 ESC 30X30mm for FPV Freestyle Flight Controller Stack DIY Parts
Product name: RuiBet 45A / 55A 4-in-1 ESC
Input voltage: 3-6S (11-27V)
Continue current: 45A / 55A * 4 channels
BEC: no
Current meter: yes
Installation: hole pitch 30.5MM/M4
Dimensions: 39.5*41MM
Firmware: BLHELI_S J_H_15_REV16_7.HEX
Weight: 14.5 grams
Omnibus F4 V3S Plus flight controller
Specification:
Item name: F4 V3S PLUS Flight Controller
Firmware:Omnibus~f4
Size: 36x36mm
Mounting holes: 30.5x30.5mm
STM32 F405 MCU
Dshot support
Drag and Drop OSD configured via Betaflight
BMI270 / MPU6500 6 axis SPI gyro & accelerometer (send at random )
SBUS / PPM AND Spketrum DSMX ports
MicroSD card blackbox
Baro (BMP280)
5v3a 9V3A BEC
On-board video filters (only 5V to VTX and camera)
Properties:
measured.
Boasting a F4 processor, on-board Betaflight OSD, MicroSD Black Box, 5v3a sbec, video filter, you&x27;ll be tuning pids with your transmitter and
Tear it to the track in no time
Note ： Only can use betaflight software.
Flytower F3 Pro Flight control Integrated OSD + 4 in 1 4in1 40A ESC BLHeli_S 2-4s Support Dshot 150/300/600 For FPV Racing Drone
Warning Instructions for use
1, Please install ANT (must be DONE) before debugging or testing VTX（and OSD）, or lead to VTX not working properly.
2, Please use proper tools to install FlyTower .It is easy to damage the PCB components by using sharp tools. (warning: Bear in mind that screws do not install too tight between every layer, so as not to destroy the PCB and electronic components).
3,When debugging and testing flight control Please remove all the propeller; Try not to test indoors, So as not to cause safety accidents. Install the propeller before a test flight, please check again.
4,Please check and adjust ESC plate welding, thus brings all the losses and problems, or you should face the consequences.
5,Please do not fly your drone near the crowd, for all the losses from the crashed aircraft, you should face the consequences.
6,For your safety, please do not use more than 4s battery, Using more than 4s battery would cause safety risk, we will not undertake any responsibility.
7, Before power on, please check the positive and negative pole again to make sure whether there is a short circuit .( you also have to check that whether there is a short circuit between your motor cables and you drone’s body).
8,Please use original screws and fixings to install FlyTower.
The flytower PRo F3/F4 board was designed basing on Omnibus/omnibusF4SD(Betaflight) FC and highly integrated with OSD, BEC, 4 in 1 BLHeli_S / Dshot 600ESC and VTX with audio ( OFF / 25/200/400 mW). It gives you al the features what you need in FPV, which make you easily get into FPV racing.
1. 4 in 1 board:
2. FC board TOP
3. FC board bottom